Plumber's Essentials: Your Key to Installing a Bathtub
Plumber's Essentials: Your Key to Installing a Bathtub
Blog Article
In this article in the next paragraph you can locate more professional advice on the subject of How to Install a Bathtub Yourself.
Mounting a bath tub isn't precisely brain surgery, yet it does need strong plumbing, carpentry, and occasionally, tiling skills. Replacing an old bath tub with a new one is additionally a moderately tough task. If the old tub is readily obtainable, the task can relocate easily; if you need to open a wall surface to eliminate the old bathtub and also place the brand-new bathtub, the task is a lot harder. In either case, the project is within a residence handyman's abilities, although you will certainly need a helper to move out the old bathtub and also embeded in the new one. Make certain you have actually certified yourself for the task as well as are comfortable trying it. Rather than working with a service provider to take control of a halfway-completed project, it is much better to take into consideration using one before you start. Possibilities are you may need a professional plumber to make tube connections.
This article will aid you install a brand-new bath tub in your washroom if you have actually already bought a brand-new tub and don't require to transform the arrangement of your previous water pipes.
Your tools as well as product checklist ought to comprise the following:
Preparing for the Setup
First of all, the supporting framework provided with the bathroom should be fitted (if needed) according to the manufacturer's instructions. Next, fit the taps or mixer to the tub. When suitable the tap block, it is very important to make sure that if the faucet comes with a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets system to prevent stress on the tub.
Fit the adaptable faucet ports to the bottom of the two taps making use of 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you utilize all of the supplied washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom must currently be ready to be suited its final placement.
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installation, then the first thing you ought to do is detach the supply of water. After doing so, turn on the taps to drain pipes any water staying in the system. The process of removing the existing faucets can be fairly troublesome because of the restricted gain access to that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will come from the pipelines. As soon as the supply pipelines have been removed, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any old sealing substance.
Prior to going on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Bathtub
Using both wood boards under its feet, position the bathtub in the required placement. The wood boards are useful in equally spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four small factors.
The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by examining the spirit level and also adjusting the feet on the bath tub up until the spirit level reviews degree.
To mount faucets, fit the bottom of the furthest flexible tap port to the ideal supply pipe by making a compression join; after that do the same for the various other faucet.
Activate the water as well as check all joints and new pipework for leakages and tighten them if essential. Fill up the bathtub and additionally check the overflow outlet and also the normal electrical outlet for leakages.
Finally, repair the bathroom paneling as defined in the producer's user's manual. Tiling as well as securing around the bathtub should wait until the tub has actually been made use of at the very least once as this will settle it right into its last placement.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end offers a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the installing opening in the bath/basin making certain that the washers are in location between the faucet and also the sink. Protect the faucet in position with the producer given backnut. As soon as the tap is securely in position, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet ports. The previous kind should be connected to the tap ends first, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the location where the bath fulfills the tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to break a stiff seal, causing the water to permeate the wall between the bath and also the tiling, leading to difficulties with dampness as well as possible leakages to the ceiling below.
You can select from a selection of coloured sealers to blend in your fixtures and also fittings. They are offered in tubes as well as cartridges, and also are capable of sealing spaces up to a size of 3mm (1/8 inch). If you have a bigger space to load, you can load it with twists of drenched newspaper or soft rope. Remember to always load the bathtub with water prior to securing, to allow for the movement experienced when the tub remains in use. The sealer can split relatively early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise conveniently available on the market. It is suggested to fit the tiles utilizing water-resistant or waterproof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that review on Tools You Need to Install a New Bathtub when browsing the search engines. Enjoyed our blog posting? Please share it. Help others discover it. We love reading our article about How to Install a Bathtub.
Book Inspection Report this page